Pesticides need to be applied accurately and uniformly. Too little pesticide results in poor pest control and reduced yields, while too much injures the crop, wastes chemicals and money, and increases the risk of polluting the environment. Achieving satisfactory results from pesticides depends heavily on five major factors:
- Positive identification of the pest.
- Choosing the least persistent and lowest toxicity pesticide that will work.
- Selecting the right equipment, particularly the right type and size of nozzle for the job.
- Applying pesticides accurately at the right time.
- Calibrating and maintaining equipment to make sure the amount recommended on the chemical label is applied.
Inspection of sprayers
Higher pesticide costs and new chemicals designed to be used in lower doses make accurate application more important than ever. There is no better time than early spring to take a closer look at your sprayer. Here are some of the things I would recommend you do this week if you don’t want to unexpectantly halt your spraying later in the season when you cannot afford delaying spraying and missing that most critical time to control weeds:
- First, if you need new or one other type of nozzles on the boom this year, do not delay purchasing new nozzles. Do it now.
- Double-check your sprayer for mechanical problems before you start using it. You won’t have time to do this when planting is in full swing.
- Clean the sprayer tank thoroughly and make sure all filters on the sprayer, especially the nozzle filters are clean.
- Clean spray nozzles to make sure they are not partially plugged. Check their flow rates, and replace the ones that are spraying more than 10 percent of the original output at a given spray pressure.
- Check the agitator in the tank to make sure it’s working properly. This is extremely important if you will be applying dry chemicals. Run water through the spray system to make sure everything is working properly.
- Always carry a spare, excellent quality pressure gage (glycerin filled) in your shop, and check the accuracy of the pressure gage on the sprayer compared to the reading you see on this spare pressure gage. Your rate controller will not know if your pressure gage is bad, and the flow rate of nozzles will be adjusted by the rate controller using the bad pressure gage.
- Once you are convinced that all sprayer parts are functioning properly, it is time to calibrate the sprayer.
Calibrate the sprayer
One can determine if the chemicals are applied at the proper rate (gallons per acre) only by carefully calibrating the sprayer. Calibration, perhaps more than anything else, will have a direct impact on achieving effective pest control and the cost of crop production. While applying too little pesticide may result in ineffective pest control, too much pesticide wastes money, may damage the crop and increases the potential risk of contaminating ground water and environment.
Results of “Sprayer Calibration Clinics” I participated in Ohio a while back, and data from several other States show that only one out of three to four applicators are applying chemicals at a rate that is within 5 % (plus or minus) of their intended rate (an accuracy level recommended by USDA and EPA). For example, if your intended rate is 20 gallons per acre, the 5% tolerable difference will be 1 gallon (5% of 20). So, your actual application rate should be as close to 20 gpa as possible, but not outside the range of 19 to 21 gpa.
How do you calibrate the sprayer?
There are several ways to calibrate a sprayer. Regardless of which method you choose, you will end up measuring the nozzle flow rate (in ounces), and the actual travel speed in miles per hour to determine the actual chemical applied in gallons per acre. Once you determine the actual application rate, you should find out if the difference between the actual rate and the intended rate is greater than 5% of the intended rate (plus or minus).
If the error is greater than the 5% tolerable error margin, you will need to reduce the error below 5% by doing one of three things: 1) Change the spraying pressure, 2) change the travel speed, and 3) change nozzles (get a different size) if the error cannot be reduced below 5% by making adjustments in either the pressure or the travel speed, or both.
It usually doesn’t take more than 30 minutes to calibrate a sprayer, and only three things are needed: a watch or smart phone to record the time when measuring the nozzle flow rate or the travel speed, a measuring tape, and a jar graduated in ounces. Please take a look at the Ohio State University Extension publication FABE-520 for an easy method for calibrating a field crop (with boom) sprayer.